Info on how to replace drive belt - Yamaha Grizzly Forum : GrizzlyOwners.Com Yamaha Grizzly Forums
 
LinkBack Thread Tools
post #1 of 5 (permalink) Old 05-11-2009, 02:16 PM Thread Starter
bad
Junior Member
 
Join Date: Apr 2008
Location: Pensacola
Posts: 3
Info on how to replace drive belt

I would like to replace my drive belt on my 2002 Grizzly. How difficult is it? Does anyone have a step by step on this? Any good belts out there? The Grizzly is 100% stock. Thanks!
bad is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old 05-11-2009, 02:23 PM
Moderator
 
hammer07's Avatar
 
Join Date: Oct 2008
Location: Marion Center
Posts: 2,696
check out Grizzhopper.com he has a great step by step with pictures

"When life's never dull, wear a hull for your skull!" -Phineas Fletcher


BLUE ('cause it's the fastest, most powerful color)'07 660 with a whole pile of stuff added!

BLUE ('cause it's STILL the fastest, most powerful color)'09 550 w/EPS

http://rocksandruts.com/
hammer07 is offline  
post #3 of 5 (permalink) Old 05-11-2009, 03:40 PM
Senior Member
 
rbdenman's Avatar
 
Join Date: Apr 2006
Location: Grahamsville
Posts: 7,680
Essentially you'll be removing the right floorboard and engine side cover, the CVT cover, and the cage around the primary. Be careful: two of the bolts holding the CVT cover on are a bit longer, and two on the cage are also longer, so know where they go! Once you've worn yourself out unbolting stuff, take the two longer bolts from the CVT cover and screw them into the 2 holes in the secondary. That'll open up the sheaves so you can get the belt off. Oh! Be careful of the end of your crankshaft after you remove the cage; there's a bearing in the cage that mates up with the end of the crankshaft, so DON'T bugger it up! Let us know how you make out!

SOLD!! 2004 Grizzly: Way too many modifications to try and list them all here...
rbdenman is offline  
post #4 of 5 (permalink) Old 05-15-2009, 12:55 AM
Member
 
Join Date: Dec 2008
Location: Brevard
Posts: 55
The hard part is getting it back on. but it can be done after you rule out ways that dont work lol.

2005 660 Hardwood Camo. 27" Outlaw MSTs Highlifter/EPI clutch kit. HMF Full exhaust. Brush Guard.1.75" wheel spacers.
dennis is offline  
post #5 of 5 (permalink) Old 05-15-2009, 11:41 AM
Senior Member
 
rbdenman's Avatar
 
Join Date: Apr 2006
Location: Grahamsville
Posts: 7,680
Oh! They're not fooling when they put that gasket around the CVT cover... MAKE SURE that it's in place; I used some grease to hold it in place on the cover.

SOLD!! 2004 Grizzly: Way too many modifications to try and list them all here...
rbdenman is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Yamaha Grizzly Forum : GrizzlyOwners.Com Yamaha Grizzly Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome